Page 1 of 1
Z750 Shortarse slip on povic I've lost 6 inches
Posted: Wed Apr 18, 2007 10:02 pm
by robracer
My pipe has lost 6 inches
sorry hoffy but I needed to practice before
chopping yours mate
following strict instructions from the Aussie streetfighters site the ugly dent has been removed well chopped off & the final result from project cut & shut is great! the look is much better & the sound is a little deeper overall i am very pleased
Now before some of the KSRC crew stand back in shock & horror of the fact that a $900 pipe can be attacked with the cutting wheel this was a second hand pipe with a dent complements from the previous owner & the landed cost of this pipe was sub $300 so there is no love lost with 6" missing
more details to come!
Re: Z750 Shortarse slip on povic I've lost 6 inches
Posted: Wed Apr 18, 2007 10:13 pm
by Gosling1
Posted: Wed Apr 18, 2007 10:17 pm
by robracer
Posted: Wed Apr 18, 2007 10:21 pm
by Gosling1
Ohh I'm sure !!!
- the small dent on the lower front section is a handy 120mm from the front of the pipe......
There must be something in the air - I am doing a chop job on the RS3 that came with the zorst system from Groggles..........its over 100mm longer than the RS3 that Hoffy is getting next week, far too bloody long. Its getting cut *in half*.....
Posted: Wed Apr 18, 2007 10:23 pm
by robracer
Posted: Wed Apr 18, 2007 11:39 pm
by Neka79
hahah u should see Greenys on his cbr...its deadset abt 5-6inches long...
Posted: Thu Apr 19, 2007 7:28 pm
by robracer
OK Next trick will be looking for more ponies... PC3 & Dyno work required here! strangely enough I had expected more popping bubbling & cracking noises when backing off but it is the same as before just slightly louder, its beaudyfuwll!!
Posted: Thu Apr 19, 2007 7:32 pm
by red_dave
Onya Rob...
Looks farkin' awesome!
Posted: Thu Apr 19, 2007 7:35 pm
by Neka79
hehe ppl werent sure whether id need a PC3 and dyno tune after fitting my new cans...boy ill tell ya i do! ..it stalls, runs lean...gives good power, but i want it smoother...
Posted: Thu Apr 19, 2007 8:44 pm
by hoffy
Looks great rob, I may need your expertise for the Yoshi, I'll let you know when it arrives.
Posted: Thu Apr 19, 2007 8:55 pm
by robracer
hoffy wrote:Looks great rob, I may need your expertise for the Yoshi, I'll let you know when it arrives.
You still waiting? slack arses! ...... hey see you sunday am?
Posted: Thu Apr 19, 2007 9:41 pm
by Gosling1
hoffy wrote:Looks great rob, I may need your expertise for the Yoshi, I'll let you know when it arrives.
The Czech is in the mail...........
Posted: Thu Apr 19, 2007 9:43 pm
by robracer
Posted: Fri Apr 20, 2007 2:33 pm
by Cath
Rob - I don't like stubbies at all, but that looks shit hot - it really suits your bike. Looks better than an undented original IMO.
Great job
Posted: Fri Apr 20, 2007 2:56 pm
by robracer
Cath wrote:Rob - I don't like stubbies at all, but that looks shit hot - it really suits your bike. Looks better than an undented original IMO.
Great job
And a dented one!
Pic shows cut past offending dent
Thanks Cath
