Number Plate Frames are nearly all gone!!!

Glen · Post by **Glen** » Thu Jun 22, 2006 8:01 am

*bump*

Update on first page

Thanks

Burky · Post by **Burky** » Fri Jun 23, 2006 10:44 pm

Look top's got mine today. Out of the pack and staight on the bike 15min later.

ZZRCHIKKY · Post by **ZZRCHIKKY** » Sat Jun 24, 2006 12:01 am

i cant get mine on , iv tried EVERYTHING

Lainie · Post by **Lainie** » Sat Jun 24, 2006 12:08 am

ZZRCHIKKY wrote:i cant get mine on , iv tried EVERYTHING

What seems to be the problem

My plates where to high so I got the bench grinder onto it

ZZRCHIKKY · Post by **ZZRCHIKKY** » Sat Jun 24, 2006 12:17 am

yes mines the same , sept we dont owna bench grinder or a chissel we dont even have any sand paper , so i tried steal wool but that was lame lol

Lainie · Post by **Lainie** » Sat Jun 24, 2006 12:18 am

ZZRCHIKKY wrote:yes mines the same , sept we dont owna bent grinder or a chissel we dont even have any sand paper , so i tried steal wool but that was lame lol

Go to K-Mart and get a cheap chissel

ZZRCHIKKY · Post by **ZZRCHIKKY** » Sat Jun 24, 2006 12:28 am

cant aford that

im saving for a trip to brisbane

and i have 2 weeks lol eak

Post by **robracer** » Sat Jun 24, 2006 8:19 am

ZZRCHIKKY wrote: i tried steal wool but that was lame lol

Well this is not suprising!

Do you have a LBS that might be able to point you in the right
direction..... as they would probably be familiar with this sort of task
Even a CAR dealership! if you get desperate

Glen · Post by **Glen** » Sat Jun 24, 2006 10:15 am

Chikky

Before you do anything drastic, what size are your plates. If they are a fairly standard 185 x 95mm design the frame should slot straight on. They are pretty tight but nothing that should require tools. NSW plates are a tad larger but they still fit.

Cheers

Glen

hoffy · Post by **hoffy** » Sat Jun 24, 2006 10:48 am

Put a bit of grease on the top and bottom of the plate, and slide in gently. it should fit, just take 1 tab at a time.

ZZRCHIKKY · Post by **ZZRCHIKKY** » Sat Jun 24, 2006 2:56 pm

ohhh i have to get the lube out them

its just a standard 2 month old qld plate but i cant seem to get it in , not even close

Post by **robracer** » Sat Jun 24, 2006 3:02 pm

[quote="ZZRCHIKKY"]ohhh i have to get the lube out them

quote]

ar ar ar wont go there

ZX10R King · Post by **ZX10R King** » Sat Jun 24, 2006 3:11 pm

ZZRCHIKKY wrote:ohhh i have to get the lube out them

but i cant seem to get it in ,

Oh dear, this is terrible news..Do you need some help?

ZZRCHIKKY · Post by **ZZRCHIKKY** » Sat Jun 24, 2006 3:21 pm

ZX9R King wrote:
ZZRCHIKKY wrote:ohhh i have to get the lube out them

but i cant seem to get it in ,

Oh dear, this is terrible news..Do you need some help?

Dirty old man

z900/zx9 · Post by **z900/zx9** » Sun Jun 25, 2006 2:22 pm

Take your helmet off before trying to fit them or lift u your tinted visor so u can see,or better still stop the bike its easier if the bike is stationary